Bikes with two battery modules
An FX or FXS with two removable power packs and an S, SR, DS or DSR with a Power Tank both run on two battery modules wired in parallel. Each module has its own BMS, its own contactor and its own log, and the motorcycle refuses to start if the second one is missing without the plug that stands in for it.
TL;DR
- The two modules join the motor controller in parallel. Each has its own BMS and contactor, and the main bike board (MBB) checks both over CAN.
- An FX or FXS runs on one pack if it sits in the front slot with the power pack connector plug fitted. Without the plug the motorcycle does not start and shows code 35.
- Modules at different charge still work together, but the motorcycle runs on the fuller one until their voltages meet. Charging both to full first puts both online from the start.
- To download both battery logs, choose "MBB + BMS + second battery (BMS1)" in the ZeroLogs app, version 0.36.7 or later.
On this page
Which Zero has two modules
Every Zero power pack contains its own battery management system (BMS). Most Zero motorcycles have one pack. The owner's manuals describe two ways to have two.
- Years
- 2014–2016
- The second module
- Quick-change packs, one or two: ZF2.8 each (ZF5.7 for two) up to 2015, ZF3.3 each (ZF6.5) in 2016.
- Years
- 2017 on
- The second module
- Only on bikes ordered with the modular system, which "may have either a single power pack or two power packs installed". The others have one fixed pack and no second slot.
- Years
- 2014–2020
- The second module
- The optional Power Tank, fitted in place of the tank storage compartment. In 2014 and 2015 it added 2.8 kWh.
- Years
- Gen3
- The second module
- A Power Tank is listed in the 2021 SR/F and 2023 DSR/X manuals, and Zero's firmware notes add the SR/S and SR from 2022. No log from one has reached us yet.
What riders' logs show
The battery logs uploaded to ZeroLogs agree with the manuals. A 2015 FX, a 2016 FXS, a 2014 S and a 2015 SR each sent a second battery log whose module serial differs from the first. No manual and no log describes a Zero with three modules.
The Gen3 Power Tank
It has its own contactor too. When it runs low the dash shows "WARNING: POWERPACK DEPLETED", and Zero's manual calls that normal: the tank opens its contactor and the main pack carries on for the rest of the ride. The plug, the codes and the download on this page are for Gen2 bikes.
How the two modules are wired
Both modules feed one high-voltage bus. Each module's positive lead runs through its own contactor, and both join the motor controller's B+ and B− terminals, so the modules are in parallel: the motorcycle sees one pack voltage, and the two capacities add up. The onboard charger feeds the same bus, so one charge fills both.
The main bike board (MBB) talks to each BMS over CAN: BMS0 for the first module, BMS1 for the second. It also runs a high-voltage interlock loop (HVIL) through each pack's signal connector, on pins Zero names "Loopback Output" and "Loopback Return". With the second module missing, that loop is open unless a plug joins the two pins, and the MBB will not let the motorcycle run.
A module goes online when its BMS closes its contactor, and that happens only when its voltage is close to the other's. Two modules at very different charge would drive a large current from one into the other, so the second one stays disconnected and the dash reports it.
In the motorcycle's log
The MBB log names each module as it joins: "Module 00 Registered" and "Module 01 Registered", each with that module's serial number and voltage, then "Closing Contractor" (sic) as its contactor closes. When a module stays out, look for "Cannot Connect Module" and "Module loopback lost".
Riding on one module
Zero supports it on an FX or FXS with removable packs, and the manual gives the steps. A Power Tank is another matter: it is wired in, and taking it out is work on the high-voltage side.
The motorcycle's log shows "Module 00 Registered" and "Module 01 Registered", then both contactors closing. Each module writes its own battery log.
On an FX or FXS, the pack sits in the front slot with the connector plug on. About half the capacity and range, and one battery log.
Dash code 35, Loopback Error, and 14 red flashes: "Needs second module, or blanking plug inserted". The same happens if the second module's connector is not seated.
The motorcycle draws on the fuller module until its voltage comes down to the other's, then connects both. Meanwhile it may show code 32, Module Variance Too High, or 57, Module Did Not Connect, and "Cannot Connect Module" in the log.
FX and FXS: from two packs to one
- 1Take the key out and support the motorcycle on a stand.
- 2Pull the key lock latch down and pull the power pack rail away from the motorcycle.
- 3Slide the rear pack out first, pushing from the other side if it sticks. Each pack weighs about 19 kg (42 lb); the 2014 manual gives 24 kg.
- 4To ride on the pack that was at the back, take the front one out too and put yours in the front slot. A single pack has to sit in the front position.
- 5Fit the power pack connector plug, which is kept on a strap under the seat. It joins the two interlock pins and touches no power contact. Without it the motorcycle will not run.
- 6Refit the rail, push the key lock up and lock it. Turn the key on and check that the motorcycle has power.
Charging a pack off the motorcycle
Zero sells an off-bike module charging adapter kit for ZF3.3 and ZF3.6 packs, which connects a removed pack to a Zero Quick Charger. The older ZF2.8 packs had adapters of their own. Without one, charge the pack in the motorcycle, alone in the front slot with the plug fitted.
S, SR, DS, DSR: without the Power Tank
Zero sold the Power Tank as a dealer-fitted accessory, and the owner's manuals give no way to remove it. Zero's service manual does describe the bike without it: the tank's inline signal connector then takes a plug that joins pin 5 (the interlock source) to pin 13 and pins 6 and 7 together. Zero sells it as the SDS loopback blanking plug, 40-08029, a different part from the FX plug. Without it the motorcycle shows code 35 and will not start.
The tank's power leads bolt to the motor controller's positive and negative cables. Once the tank is out, take that harness off at the controller too: left in place, its loose end is live from the main pack whenever the main contactor is closed. All of it is work on a discharged high-voltage system, for a dealer or a technician trained on Zero high voltage.
Adding the second module
Zero says FX modules can be mixed whatever their charge or age. The motorcycle then draws on the fuller one until its voltage comes down to the other's, and only then connects both, so power and range are lower until they meet. To have both online from the start, charge both to full first.
FX and FXS: from one pack to two
- 1Take the key out, support the motorcycle and take the rail off.
- 2Take the power pack connector plug off and strap it under the seat.
- 3Slide the second pack into the rear slot until its connectors engage.
- 4Refit the rail and lock it. Turn the key on and check that the motorcycle has power.
A module that is new to the motorcycle
Zero lists its ZF3.6 module (part 46-08117) for the 2015 and 2016 FX and FXS and the 2017 to 2019 modular FX and FXS. A pack bought separately may carry different BMS firmware from the rest of the motorcycle: a Zero dealer checks and updates the MBB and every BMS from the diagnostic port, and sets the clock of a newly fitted BMS.
A Power Tank is always fitted by a dealer, with Zero's fasteners and harness kit (12-08011). Zero listed the ZF2.8 tank for the 2014 and 2015 S, SR and DS and the ZF3.6 tank from 2015, and neither shares the tank area with the Charge Tank.
Codes that point at a module
A Gen2 Zero shows a two-digit code in the dash's Display A, and the red warning light flashes a count. These are the ones a two-module motorcycle meets. On Gen3 bikes the same numbers mean other faults.
- What the manual calls it
- Loopback Error (14 red flashes): "Needs second module, or blanking plug inserted"
- What it means here
- Module 1 is missing or its connector is loose, and no plug closes the loop
- What to do
- Fit the plug, or reseat the second module
- What the manual calls it
- Module Variance Too High (10 red flashes)
- What it means here
- The two modules' voltages are too far apart for both to connect
- What to do
- Ride or charge until they meet; if it stays, the manual says to contact Zero or a dealer
- What the manual calls it
- Module Did Not Connect
- What it means here
- A module's contactor did not close
- What to do
- The manual: "may only require recharging"
Downloading both logs
The motorcycle sends the first battery's log unless it is told to switch to the second. On Gen2-format motorcycles the ZeroLogs app can tell it to:
- 1Connect the app to the motorcycle and tap "Download logs".
- 2Choose "MBB + BMS + second battery (BMS1)". The green "MBB + BMS (full)" button reads the first battery only.
- 3Keep the phone near the motorcycle until the card shows 3/3.
- 1MBB logthe motorcycle
- 2BMS0 logmodule 0
- 3Switch to BMS1the app asks
- 4BMS1 logmodule 1
- 5Switch back to BMS0always
Key off, on the charger
The key can stay off. A 2016 FXS with two modules gave all three logs while it charged on its onboard charger. That also spares the headlight, which that model cannot switch off and which stays lit with the key on.
App version
Use app 0.36.7 (November 2026) or later. Versions 0.36.5 and 0.36.6 sent the switch with its bytes in the wrong order, so the second module's log was never read. So far the second-battery read is confirmed on one motorcycle, a 2016 FXS; if you try it on another, tell us how it went.
When there is no second log
The app says why and keeps the motorcycle's log and the first battery's either way:
- "No second battery answered" or "The motorcycle did not switch to a second battery": expected on a one-module motorcycle.
- "The motorcycle sent the first battery's log again": expected on a one-module bike. On a two-module bike, check the app version, and send a report if it happens with 0.36.7 or later.
- "Second battery log … only N of M blocks": the motorcycle ended the log early. What was read is kept; download again later.
Logs you already have
Upload them as they are. On Gen2-format files, _BMS0_ is the first module and _BMS1_ the second (some tools write _BmsD0_ and _BmsD1_). Gen3 battery logs are usually named _BMS1_ even with one module, which is why the name is not what ZeroLogs goes by: every battery log starts with a header carrying its module's serial numbers, and each file is matched to its module by them. A pack moved between slots keeps its own history.
How ZeroLogs shows the modules
On your Batteries page each module is a battery of its own, with its own card: its cells, temperatures and history come from that module's logs only.
The charge curve, the cells at the top of a charge, the cell-balance trend, the parking details, the log viewer and the cell charts beside a motorcycle log show one module at a time, with a switch between them. On a module's card, each charge's lowest and highest cell come from that module's own log.
Each module's card shows that module's own health: its share of each charge, from its own log, over the charge the motorcycle gained, set against its own size. Both modules are measured on the same charges, the ones both logs recorded, and a charge counts only when the two together make sense for the whole pack, so the two add up to the pack. On a 2016 FXS, over the same 17 charges, the two modules read 63 % and 58 % and together 60 %, against 61 % for the whole pack. The card says which years those charges are from, and says when they are old. The two modules work together, so one that holds less lowers the whole motorcycle's range.
One charge's split between the two modules scatters: on that FXS a charge sat 17 % from the typical split at the median. So the Batteries page also compares the two modules over many charges, and says one holds less only when the whole 95 % range of the comparison is more than 10 % away. It needs 20 charges, and it says plainly when the charges cannot tell yet.
A Power Tank gets its own health too: it may have been added after the motorcycle was bought, and it may wear faster than the main pack. The main pack is set against the motorcycle's own pack size, and the Power Tank against the size you declared or, failing that, the one Zero gave the Power Tank of its serial's year: 2.8 kWh in 2014 and 2015 (the owner's manuals), ZF3.3 in 2017 (Zero's 2017 lineup) and ZF3.6 from 2018 (Zero's accessory pages). Zero gives no figure for 2016, so a 2016 Power Tank is taken as that year's ZF3.3 module, and its card says so. The comparison then sets each against its own size, so a Power Tank wearing faster shows.
Each battery's health needs its own log. Where the motorcycle names two batteries but only one log has come, the page says so and asks for the second, downloaded with the app or uploaded.
Frequently asked questions
Can I ride an FX or FXS with only one battery?
Yes. Put the pack in the front slot and fit the power pack connector plug, which is kept on a strap under the seat. Without the plug the motorcycle does not start and shows code 35.
I lost the connector plug. Where do I get one?
From a Zero dealer. For the FX, Zero's parts catalogue lists a "module blanking plug assembly", 40-06885 (2015 FX); for the S, SR, DS and DSR it is the SDS loopback blanking plug, 40-08029. Ask for the one that fits your year. Until it arrives, ride with both modules fitted.
Can I ride an S or SR with the Power Tank taken out?
Yes, with the SDS loopback blanking plug in the tank's connector and the tank's power harness taken off at the controller. That is high-voltage work for a dealer. Without the plug the motorcycle shows code 35 and will not start.
Why does the second module not connect after a swap?
Its voltage is too far from the other module's, so its contactor stays open (code 32 or 57). The motorcycle runs on the fuller one until they meet. Charge both to full to avoid it.
Why does only one battery log arrive from my two-module Zero?
The motorcycle sends the first battery's log unless it is asked to switch. In the ZeroLogs app choose "MBB + BMS + second battery (BMS1)" (app 0.36.7 or later).
The procedures, pinouts and codes are Zero's, from the manuals above. The rest of the wiring follows the archived zeromanual.com wiki. The download was measured on a 2016 FXS with two modules on 14 November 2026: the app's second-battery read matched an earlier download of the same module on 1,007 of 1,024 blocks, the rest being what the battery logged in between.
Sources:
- Zero Motorcycles: 2014 Zero FX owner's manual (OM-FX-MY14), p. 4.6, "Every power pack contains a Battery Management System", and p. 4.7, the pack weight (opens in a new tab)
- Zero Motorcycles: 2016 Zero FX and FXS owner's manual (OM-XMX-MY16-English-04), p. 5.3, the quick-change power pack, pp. 7.2 to 7.6, the red flashes and dash codes, and pp. 3.17 and 3.18, the handlebar controls (opens in a new tab)
- Zero Motorcycles: 2018 Zero FX and FXS owner's manual (OM-XMX-MY18-English-AE), p. 5.3, "either a single power pack or two power packs" (opens in a new tab)
- Zero Motorcycles: 2021 Zero FX and FXS owner's manual (English-05), pp. 5.3 and 5.4, removing and installing the packs, the front position and the power pack connector plug (opens in a new tab)
- Zero Motorcycles: 2015 Zero S and DS owner's manual (OM-SDS-MY15-English), p. 3.22, the Power Tank adds 2.8 kWh, and p. 7.1, the warranty (opens in a new tab)
- Zero Motorcycles: 2016 Zero S and DS owner's manual (OM-SDS-MY16-English-06), p. 3.22, the Power Tank, and p. 9.1, its integrated battery management system (opens in a new tab)
- Zero Motorcycles: 2020 Zero S and DS owner's manual (OM-SDS-MY20-English-03), p. 3.24, the Power Tank (opens in a new tab)
- Zero Motorcycles: 2021 Zero SR/F owner's manual (English-05), p. 5.8, the Power Tank (opens in a new tab)
- Zero Motorcycles: 2023 Zero DSR/X owner's manual (88-09970-AK), p. 5.15, the Power Tank (opens in a new tab)
- Zero Motorcycles: FX and FXS service manual (8811943-AF), p. 10-10, the trouble codes, and p. 20-15, the modular power pack harness (opens in a new tab)
- Zero Motorcycles: 2016 Zero FXS service manual, the power pack signal connectors C137 and C147 (S5 and S7, the HVIL loopback) (opens in a new tab)
- Zero Motorcycles: 2018 Zero DSR service manual, the Power Tank inline connector without a power pack, and the tank power harness (opens in a new tab)
- Zero Motorcycles: Z-Force 3.6 power pack module, the FX and FXS "ridden using either one or two" modules (opens in a new tab)
- Zero Motorcycles: Z-Force 3.6 power pack module, as listed in 2019 (part 46-08117, fitment, state of charge) (opens in a new tab)
- Zero Motorcycles: off-bike module charging adapter kit (opens in a new tab)
- Zero Motorcycles: Z-Force 3.6 Power Tank for the S (opens in a new tab)
- Zero Motorcycles: firmware release notes, Power Tank support on Gen3 (opens in a new tab)
- zeromanual.com (archived): Switch Dual to Single Battery, the FX plug and its two pins (opens in a new tab)
- zeromanual.com (archived): BMS CANBus Loopback, the BMS1 connector and its loopback plug (opens in a new tab)
- zeromanual.com (archived): Power Tank, its BMS, contactor, harness and installation (opens in a new tab)
ZeroLogs is an independent tool, not affiliated with Zero Motorcycles, Inc. Work on a high-voltage pack only as Zero's manuals describe, and leave anything beyond that to a Zero dealer.