How the Z-Force motor works
Every Zero from 2014 on runs one of five Z-Force motors. They all work the same way: the controller sends three currents through the coils of the stator, and the magnets in the rotor follow the field those currents make. This page opens one up in 3D and compares the five from Zero's own manuals.
TL;DR
- A Z-Force is a three-phase motor with permanent magnets in the rotor, ten poles of them, and one copper coil on each stator tooth. Zero calls it radial flux and passively air-cooled: the fins on the case do all the cooling.
- Up to 2015 the magnets sat on the rotor surface. During 2016 they moved inside the rotor steel ("interior permanent magnet"), on every bike from 2017, and the R in 75-7R means magnets rated for higher temperature.
- The number after the dash is the rotor length in centimetres: 5 cm in the 75-5 and 7 cm in the 75-7. A longer rotor carries more magnet and gives more torque for the same current.
- The controller sets the power. The 2014 S and SR shared the same 75-7: with a 420 A controller it gave 92 Nm, with 660 A it gave 144 Nm. The 2024 SR and SR/F share the 75-10 and the same rule holds.
- Peak power runs from 32.7 kW on the 2017 FX family to 84 kW on the 2024 SR/F and SR/S, all from a 102 V battery.
Inside a Z-Force, in 3D
Pick a motor and a model year, then drag to turn the motor. The tour walks through the case, the belt drive, the coils, the magnets, the encoder, driving and regen, and the speed and throttle move with it. Any touch pauses it. The numbers beside the model come from the same calculation that turns the rotor and lights the coils: motor speed from road speed and the bike's gearing, torque from Zero's peak figures, and the angle at which the controller places its field against the magnets.
More
The case
The FX family, and the S, SR, DS and DSR up to 2023, use this case: a bronze barrel covered in thin fins that run along the shaft, closed by two black cast end caps with four bolt ears. Zero calls it passively air-cooled, so the fins do all the cooling. The three phase cables and the encoder lead leave through the flat strip on top.
Flat at 106 Nm up to about 70 km/h, then torque falls so power stays at 33 kW. Dashed: the regen side, drawn at half the drive curve.
Rotation is slowed 150 times so the magnets can be followed. The case, the belt drive, the gearing and every figure follow Zero's manuals and photos. The inside is a faithful layout but a drawing: Zero publishes the ten poles, not the number of stator teeth or the shape of the magnets, and the model draws twelve teeth with a coil on each.
On this page
How an electric motor turns
Two magnets pull on each other: a north pole attracts a south pole and pushes away another north. An electric motor uses that pull to turn a shaft. The moving part, the rotor, carries permanent magnets. Around it sits the stator, a ring of steel teeth wound with copper coils. Current through a coil turns its tooth into a magnet, and the rotor's magnets are pulled toward it.
One coil would pull the rotor to a stop. To keep it turning, the pull has to move round the ring ahead of the magnets, and three currents do that. The controller feeds three groups of coils, called phases U, V and W, with currents that rise and fall like waves, each a third of a cycle behind the one before. Where one phase peaks, its coils make the strongest pole, so the strongest pole walks round the stator and the rotor follows it.
The battery gives direct current at about 102 V. The controller is an inverter: it switches that direct current on and off thousands of times a second to build the three waves, and it sets both how big they are (the torque) and how fast they cycle (the speed). Zero rates each controller by its current, from 420 A on the 2014 FX to 900 A on the SR/F.
A Z-Force has ten rotor poles, five north and five south. One electrical cycle moves the field past one north and one south, a fifth of a turn, so the currents cycle five times per revolution. At the SR/F's top speed of 200 km/h the motor turns at about 7,600 rpm and the controller drives its coils at about 630 cycles a second.
The parts, and what Zero says about each
Zero builds two kinds of case around the same idea. The FX family, and the S, SR, DS and DSR up to 2023, use a bronze-coloured barrel with thin fins running along it, closed by two black cast end caps with four bolt ears. The SR/F and SR/S from 2020, the SR from 2022, the DSR/X from 2023, and the S, DS and DSR from 2024 use a larger drum with fins running round it, held in the frame by black doubler plates. Zero says the 2024 S shares the motor hardware of the SR/F and the DS that of the DSR/X.
Case and cooling
Every manual calls the motor passively air-cooled: there is no fan and no coolant, and the heat leaves through the fins into the air going past. Zero's own report on the motor says the stator is heat-shrink pressed into the case, so the case itself carries the heat away from the coils. On the drum-cased bikes the manuals add "enhanced thermal efficiency". Zero's drawing of the 75-5 and 75-7 gives a 224 mm body and 269 mm over the fins.
Stator and coils
The stator is a stack of thin steel sheets, laminations, with teeth on the inside, each wound with copper. Thin sheets instead of solid steel keep the swirling currents the changing field would otherwise set up in the iron down to a minimum. The coils are joined into the three phases, and three heavy cables, which the service manuals call M1, M2 and M3, run from them to the controller. Zero's report puts hand-winding one at about 12 hours of labour.
Rotor and magnets
The rotor carries ten permanent-magnet poles. Zero's first ZF75 design had twenty, but the controller of the time could not run it above about 2,000 rpm, so Zero halved the pole count to lower the frequency the controller had to produce.
The owner's manuals show when the magnets moved. Up to 2015 they say "radial flux permanent magnet", magnets on the rotor surface. In 2016 Zero sold both kinds: the S and DS with the ZF9.8 battery kept surface magnets and those with the ZF13.0 got interior ones, and the press kit listed a 75-5 and a 75-5 IPM, a 75-7 and a 75-7 IPM. From 2017 every manual says "interior permanent". Buried in the rotor steel, the magnets are held mechanically and better protected from heat, and the steel between them adds torque of its own as the field pulls on it. The 75-7R has magnets rated for higher temperatures; the 2014 and 2015 SR already listed hi-temp magnets on a 75-7.
Shaft, bearings and belt pulley
The rotor turns on two bearings, the same large size at each end, which Zero chose to cut the number of different parts. The shaft is splined. The belt pulley slides onto it with retaining compound and is held by a bolt tightened to 71 Nm on the drum-cased bikes. On the FX, S and DS the swingarm pivots on the frame, so the belt is tensioned by moving the rear axle. On the drum-cased bikes the swingarm bolts to the motor's two outer bearing covers and swings round the motor's own axis, so the distance from pulley to wheel sprocket does not change as the suspension moves.
Encoder
To place its field just ahead of the magnets, the controller has to know exactly where the rotor is. A small magnet on the end of the shaft spins in front of an encoder, a magnetic angle sensor that RLS supplies to Zero. The two have to agree on where zero degrees is, so a new motor comes with a sticker giving its offset angle, and after a motor or controller swap the dealer types it in and runs encoder commissioning with the rear wheel off the ground. The S, SR and SR/F service manual says the new reading must not be more than 5 degrees from the old one, and that the motorcycle must not be ridden if it is.
Every service manual warns that prying or hammering on the motor shaft, or using an impact gun on the pulley bolt, can damage the encoder or its magnet and make the bike unsafe.
What 75-5, 75-7 and 75-10 mean
Zero's report on the motor says it directly: the ZF75-7 "has a rotor length of 7cm" and the ZF75-5 has "a 5 cm rotor length". Same diameter, more length: more magnet and more copper working at once, so more torque for the same current. Zero's drawings show the 75-7 20 mm longer overall than the 75-5 and give the 75-5 an expected production weight of 14 kg; a Zero engineer put the 75-7 at about 38 lb (17 kg) in 2015.
By the same naming the 75-10 has a 10 cm rotor, though Zero has not said so. No Zero document explains the 75.
The letters: R is the 75-7 with hi-temp magnets (SR and DSR, 2016 to 2023). X is the version in the DSR/X and, from 2024, the DSR; the 2023 DSR/X manual calls it "75-10 5T" and later manuals "75-10X". It gives more torque than the 75-10 for the same controller current, 229 Nm at 900 A against 190 Nm on the SR/F. The 2024 S and DS took the 75-7 name into the drum case.
Why the same motor makes different power
Torque in this kind of motor follows current: twice the current through the coils, about twice the pull on the magnets. The controller decides how much current the motor gets, so it sets the torque, and Zero prints its rating on every specification page. On bikes sold at the same time with the same motor the result is close to exact. In 2014 the S and SR both had a 75-7. The S had a 420 A controller and 92 Nm; the SR had 660 A and 144 Nm. Both ratios are 1.57. In 2024 the SR and SR/F both had a 75-10: 785 A gave 166 Nm and 900 A gave 190 Nm, a ratio of 0.87 both ways.
Peak power is torque times speed, and the motor reaches it at what is called base speed. Below base speed the controller can push full current and the torque is flat. Above it, the voltage the spinning magnets generate in the coils approaches the battery's, so the controller can only keep current flowing by shifting its field further ahead of the magnets, which partly cancels them (field weakening). From there torque falls as speed rises and power stays about flat. Zero publishes the two peaks and not the curve, so the curve on this page is worked out from them.
Europe adds a third control: the licence versions. The 2024 to 2026 S in its A1 version has the same 75-7 and 600 A controller as the full-power S, but 45 kW peak and 139 km/h instead of 51 kW and 167 km/h, and its manual adds an 11 kW "maximum continuous-rated 30 minutes power", the figure the A1 licence goes by. The older "Zero S (11kW)" versions of 2017 to 2023 follow the same idea, and their pages still print 44 kW peak for the 75-7. The A2 versions of the SR and DSR cut the controller current (665 A and 670 A) and with it the torque.
Regen is the same machine run backwards. When the throttle closes, the controller places its field behind the magnets instead of ahead, the magnets drag on it, the coils generate, and the current goes back into the battery.
Not every point fits
The rule holds for bikes sold side by side. Across years it bends, because Zero changed magnets and controllers inside the same motor name: the 75-5 gave 95 Nm at 420 A in 2014 and 106 Nm at 550 A from 2017, and the 2022 and 2023 SR printed 900 A with 166 Nm, less than the SR/F at the same rating.
From motor to wheel
The motor does not turn the wheel directly. A toothed belt runs from a small pulley on the motor shaft to a large sprocket on the rear wheel, and the ratio of their teeth is the only gear the bike has. On a 2024 SR/F the pulley has 20 teeth and the sprocket 90, so the motor turns 4.5 times for each turn of the wheel. That multiplies the motor's torque by 4.5 at the wheel and divides its speed by 4.5. By our arithmetic the SR/F's 190 Nm become about 2,700 N of push where the tyre meets the road, and its 200 km/h top speed asks the motor for about 7,580 rpm [9].
One gear is enough because an electric motor gives its full torque from a standstill and still pulls at several thousand rpm. A petrol engine makes little torque at low revs and works best in a narrow band, so it needs a gearbox to stay in that band. The Z-Force has no band to stay in. The controller can give it full current from zero rpm, so the belt only has to set one balance between pull and speed.
Zero has used eight pairs. The 2014 to 2016 bikes had 130- and 132-tooth sprockets with 25- to 30-tooth pulleys, from 5.28:1 on the FX and FXS to 4.33:1 on the 2016 SR. From 2017 almost every bike has a 90-tooth sprocket and a 20-tooth pulley, 4.50:1. The FX family went shorter in 2018, with 18 teeth on the motor and 5.00:1, which suits a light off-road bike that tops out at about 137 km/h. The DSR/X and the 2024 and later DSR went longer, with 22 teeth and 4.09:1 behind the 75-10X's extra torque [4]-[11].
The gearing does not set the top speed. The controller does. The 2020 S and the 2021 S in its 11 kW licence version have the same 75-7, the same 20/90 belt and the same rear tyre, and Zero prints 153 km/h for one and 139 km/h for the other, which is about 5,820 and 5,290 rpm at the motor [7]. The fastest Zeros, the SR/F and SR/S at 200 km/h, run their motor at about 7,580 rpm. The 2017 FX reaches its printed top speed at about 5,040 rpm, the lowest of any model year.
Divide the push at the tyre by the bike's curb weight and the bikes can be compared on one scale. The S and DS give about 7.1 to 8.8 newtons per kilogram of bike, the SR and DSR 9.8 to 11.1, the FX family 11.2 to 12.7, the SR/F and SR/S 11.6 to 12.3 and the DSR/X 11.7 to 11.9. Since 2017 nearly all of them have the same 4.50:1 belt, so the spread comes from the motor and the controller's current, not from the gearing. It is a theoretical figure: it leaves out the rider, the belt's losses and the tyre's grip, so read it as a comparison between bikes, not as an acceleration.
Gearing also matters for the logs. A Gen2 bike records motor rpm, not road speed, so turning its log into a speed depends on the gearing: with a different pulley, the same rpm means a different speed. Gen3 bikes record road speed directly.
| As built, 20/90 | With 22/90 | Change | |
|---|---|---|---|
| Reduction | 4.50:1 | 4.09:1 | -9 % |
| Road speed per 1,000 motor rpm | 26.4 km/h | 29.0 km/h | +10 % |
| Motor rpm at 200 km/h | 7,580 | 6,890 | -9 % |
| Peak push at the tyre | 2,720 N | 2,470 N | -9 % |
| Per kg of bike (227 kg) | 12.0 N/kg | 10.9 N/kg | -9 % |
The five motors compared
Every figure here is the one printed in Zero's owner's manual for that model year. Power and torque come from the European specification pages, which print them for every year from 2017. For 2014 to 2016, whose manuals print neither, the power and torque come from Zero's own spec pages of the time. Where a manual prints several versions of a bike, this table uses the full-power one; the full list of versions is in the table at the end of the section.
- 75-5
- FX, FXS, FXE
- 75-7
- S, DS; SR 2014–2015
- 75-7R
- SR, DSR
- 75-10
- SR, SR/F, SR/S
- 75-10X
- DSR, DSR/X
- 75-5
- 2014–2025
- 75-7
- 2014–2026
- 75-7R
- 2016–2023
- 75-10
- 2020–2026
- 75-10X
- 2023–2026
- 75-5
- 32.7–34 kW
- 75-7
- 40–51 kW
- 75-7R
- 50–52 kW
- 75-10
- 55–84 kW
- 75-10X
- 60–75 kW
- 75-5
- 44–46
- 75-7
- 54–68
- 75-7R
- 67–69
- 75-10
- 74–113
- 75-10X
- 80–100
- 75-5
- 44–46
- 75-7
- 54–69
- 75-7R
- 68–71
- 75-10
- 75–114
- 75-10X
- 82–102
- 75-5
- 95–106 Nm
- 75-7
- 92–144 Nm
- 75-7R
- 144–146 Nm
- 75-10
- 166–190 Nm
- 75-10X
- 195–229 Nm
- 75-5
- 420–550 A
- 75-7
- 420–660 A
- 75-7R
- 660–775 A
- 75-10
- 785–900 A
- 75-10X
- 765–900 A
- 75-5
- 102 V
- 75-7
- 102 V
- 75-7R
- 102 V
- 75-10
- 102 V
- 75-10X
- 102 V
- 75-5
- 132–137 km/h
- 75-7
- 139–167 km/h
- 75-7R
- 158–164 km/h
- 75-10
- 167–200 km/h
- 75-10X
- 167–180 km/h
hp as Zero prints it; PS or CV (metric horsepower) is worked out from the kW. The unit switch above the 3D view changes the figures in the viewer, the motor cards and the bike table, not this one. Controller: the current rating Zero prints for it. Battery: every Z-Force pack is 28 cells in series, 102 V nominal (Zero prints 102.2 V) and about 117 V full. The 75-7 column includes the S and DS 11 kW licence versions of 2021–2023, the only versions whose pages print power.
- Rotor length
- 5 cm
- Magnets
- On the rotor surface on the FX to 2016, inside the rotor from the 2016 FXS on
- Case
- Finned barrel
- Rotor length
- 7 cm
- Magnets
- On the surface to 2015, inside the rotor from 2016 (except the 2016 S and DS with the ZF9.8 battery)
- Case
- Finned barrel to 2023, ring-fin drum from 2024
- Rotor length
- 7 cm
- Magnets
- Inside the rotor, rated for higher temperature
- Case
- Finned barrel
- Rotor length
- 10 cm by the naming
- Magnets
- Inside the rotor
- Case
- Ring-fin drum
- Rotor length
- 10 cm by the naming
- Magnets
- Inside the rotor
- Case
- Ring-fin drum
Rotor lengths of the 75-5 and 75-7 from Zero's report [1]; Zero has not stated the 75-10's. Magnets from the owner's manuals' own wording ("radial flux permanent" or "interior permanent") and the 2016 press kit [2].
Model year by model year
The SR shows how often a model changed motor: a 75-7 in 2014 and 2015, the 75-7R from 2016, the 75-10 in the new frame from 2022. The S and DS kept the 75-7 throughout and moved it into the drum case in 2024, with 51 kW at full power.
Every model year (85), with the page each figure is printed on
| Bike | Motor | kW | PS | Nm | Controller | Top speed | Version | Source |
|---|---|---|---|---|---|---|---|---|
| FX 2014 | 75-5 | 33 | 45 | 95 | 420 A | 137 km/h | Zero spec page | |
| FX 2015 | 75-5 | 33 | 45 | 95 | 420 A | 137 km/h | Zero spec page | |
| FX 2016 | 75-5 | 33 | 45 | 95 | 420 A | 137 km/h | Zero spec page | |
| FX 2017 | 75-5 | 32.7 | 44 | 106 | 550 A | 137 km/h | manual p. 8.1 | |
| FX 2018 | 75-5 | 33 | 45 | 106 | 550 A | 137 km/h | manual p. 8.1 | |
| FX 2019 | 75-5 | 33 | 45 | 106 | 550 A | 137 km/h | manual p. 8.1 | |
| FX 2020 | 75-5 | 33 | 45 | 106 | 550 A | 137 km/h | manual p. 8.2 | |
| FX 2021 | 75-5 | 33 | 45 | 106 | 550 A | 137 km/h | manual p. 8.2 | |
| FX 2022 | 75-5 | 33 | 45 | 106 | 550 A | 137 km/h | manual p. 8.2 | |
| FX 2023 | 75-5 | 33 | 45 | 106 | 550 A | 137 km/h | manual p. 8.2 | |
| FX 2024 | 75-5 | 34 | 46 | 106 | 550 A | 137 km/h | manual p. 8.7 | |
| FX 2025 | 75-5 | 34 | 46 | 106 | 550 A | 137 km/h | manual p. 8.7 | |
| FXE 2022 | 75-5 | 33 | 45 | 106 | 550 A | 132 km/h | manual p. 8.6 | |
| FXE 2023 | 75-5 | 33 | 45 | 106 | 550 A | 132 km/h | manual p. 8.6 | |
| FXE 2024 | 75-5 | 34 | 46 | 106 | 550 A | 137 km/h | manual p. 8.9 | |
| FXE 2025 | 75-5 | 34 | 46 | 106 | 550 A | 137 km/h | manual p. 8.9 | |
| FXS 2016 | 75-5 | 33 | 45 | 95 | 420 A | 132 km/h | Zero spec page | |
| FXS 2017 | 75-5 | 32.7 | 44 | 106 | 550 A | 137 km/h | manual p. 8.3 | |
| FXS 2018 | 75-5 | 33 | 45 | 106 | 550 A | 132 km/h | manual p. 8.3 | |
| FXS 2019 | 75-5 | 33 | 45 | 106 | 550 A | 132 km/h | manual p. 8.3 | |
| FXS 2020 | 75-5 | 33 | 45 | 106 | 550 A | 132 km/h | manual p. 8.4 | |
| FXS 2021 | 75-5 | 33 | 45 | 106 | 550 A | 132 km/h | manual p. 8.6 | |
| DS 2016 | 75-7 | 40 | 54 | 92 | 420 A | 158 km/h | ZF13.0 | Zero spec page |
| DS 2017 | 75-7 | 45 | 61 | 110 | 550 A | 158 km/h | manual p. 8.9 | |
| DS 2018 | 75-7 | 45 | 61 | 110 | 550 A | 158 km/h | manual p. 8.10 | |
| DS 2019 | 75-7 | 45 | 61 | 110 | 550 A | 158 km/h | manual p. 8.10 | |
| DS 2020 | 75-7 | 45 | 61 | 110 | 550 A | 158 km/h | manual p. 8.10 | |
| DS 2021 | 75-7 | 44 | 60 | 109 | 550 A | 139 km/h | 11kW, ZF14.4 | manual p. 8.6 |
| DS 2022 | 75-7 | 44 | 60 | 109 | 550 A | 139 km/h | 11kW | manual p. 8.4 |
| DS 2023 | 75-7 | 44 | 60 | 109 | 550 A | 139 km/h | 11kW | manual p. 8.4 |
| DS 2024 | 75-7 | 51 | 69 | 132 | 600 A | 167 km/h | Full Power | manual p. 8.6 |
| DS 2025 | 75-7 | 51 | 69 | 132 | 600 A | 167 km/h | Full Power | manual p. 8.6 |
| DS 2026 | 75-7 | 51 | 69 | 132 | 600 A | 167 km/h | Full Power | manual p. 8.6 |
| S 2014 | 75-7 | 40 | 54 | 92 | 420 A | 153 km/h | Zero spec page | |
| S 2015 | 75-7 | 40 | 54 | 92 | 420 A | 158 km/h | Zero spec page | |
| S 2016 | 75-7 | 40 | 54 | 92 | 420 A | 153 km/h | ZF13.0 | Zero spec page |
| S 2017 | 75-7 | 45 | 61 | 110 | 550 A | 158 km/h | manual p. 8.3 | |
| S 2018 | 75-7 | 45 | 61 | 110 | 550 A | 153 km/h | manual p. 8.4 | |
| S 2019 | 75-7 | 45 | 61 | 110 | 550 A | 153 km/h | manual p. 8.4 | |
| S 2020 | 75-7 | 45 | 61 | 110 | 550 A | 153 km/h | manual p. 8.4 | |
| S 2021 | 75-7 | 44 | 60 | 109 | 550 A | 139 km/h | 11kW, ZF14.4 | manual p. 8.2 |
| S 2022 | 75-7 | 44 | 60 | 109 | 550 A | 139 km/h | 11kW | manual p. 8.2 |
| S 2023 | 75-7 | 44 | 60 | 109 | 550 A | 139 km/h | 11kW | manual p. 8.2 |
| S 2024 | 75-7 | 51 | 69 | 132 | 600 A | 167 km/h | Full Power | manual p. 8.6 |
| S 2025 | 75-7 | 51 | 69 | 132 | 600 A | 167 km/h | Full Power | manual p. 8.6 |
| S 2026 | 75-7 | 51 | 69 | 132 | 600 A | 167 km/h | Full Power | manual p. 8.6 |
| SR 2014 | 75-7 | 50 | 68 | 144 | 660 A | 164 km/h | Zero spec page | |
| SR 2015 | 75-7 | 50 | 68 | 144 | 660 A | 164 km/h | Zero spec page | |
| DSR 2016 | 75-7R | 50 | 68 | 144 | 660 A | 158 km/h | Zero spec page | |
| DSR 2017 | 75-7R | 51.5 | 70 | 146 | 775 A | 164 km/h | manual p. 8.11 | |
| DSR 2018 | 75-7R | 52 | 71 | 146 | 775 A | 158 km/h | manual p. 8.12 | |
| DSR 2019 | 75-7R | 52 | 71 | 146 | 775 A | 158 km/h | manual p. 8.12 | |
| DSR 2020 | 75-7R | 52 | 71 | 146 | 775 A | 163 km/h | manual p. 8.12 | |
| DSR 2021 | 75-7R | 52 | 71 | 146 | 775 A | 163 km/h | manual p. 8.8 | |
| DSR 2022 | 75-7R | 52 | 71 | 146 | 775 A | 163 km/h | manual p. 8.6 | |
| DSR 2023 | 75-7R | 52 | 71 | 146 | 775 A | 163 km/h | manual p. 8.6 | |
| SR 2016 | 75-7R | 50 | 68 | 144 | 660 A | 164 km/h | Zero spec page | |
| SR 2017 | 75-7R | 51.5 | 70 | 146 | 775 A | 164 km/h | manual p. 8.5 | |
| SR 2018 | 75-7R | 52 | 71 | 146 | 775 A | 164 km/h | manual p. 8.6 | |
| SR 2019 | 75-7R | 52 | 71 | 146 | 775 A | 164 km/h | manual p. 8.6 | |
| SR 2020 | 75-7R | 52 | 71 | 146 | 775 A | 163 km/h | manual p. 8.6 | |
| SR 2021 | 75-7R | 52 | 71 | 146 | 775 A | 163 km/h | manual p. 8.4 | |
| SR 2022 | 75-10 | 55 | 75 | 166 | 900 A | 167 km/h | manual p. 8.2 | |
| SR 2023 | 75-10 | 55 | 75 | 166 | 900 A | 167 km/h | manual p. 8.2 | |
| SR 2024 | 75-10 | 64 | 87 | 166 | 785 A | 167 km/h | Full Power | manual p. 8.14 |
| SR 2025 | 75-10 | 64 | 87 | 166 | 785 A | 167 km/h | Full Power | manual p. 8.14 |
| SR/F 2020 | 75-10 | 82 | 111 | 190 | 900 A | 200 km/h | manual p. 8.2 | |
| SR/F 2021 | 75-10 | 82 | 111 | 190 | 900 A | 200 km/h | manual p. 8.2 | |
| SR/F 2022 | 75-10 | 82 | 111 | 190 | 900 A | 200 km/h | manual p. 8.10 | |
| SR/F 2023 | 75-10 | 82 | 111 | 190 | 900 A | 200 km/h | manual p. 8.10 | |
| SR/F 2024 | 75-10 | 84 | 114 | 190 | 900 A | 200 km/h | Full Power | manual p. 8.22 |
| SR/F 2025 | 75-10 | 83 | 113 | 190 | 900 A | 200 km/h | Full Power | manual p. 8.22 |
| SR/F 2026 | 75-10 | 83 | 113 | 190 | 900 A | 200 km/h | Full Power | manual p. 8.14 |
| SR/S 2020 | 75-10 | 82 | 111 | 190 | 900 A | 200 km/h | manual p. 8.2 | |
| SR/S 2021 | 75-10 | 82 | 111 | 190 | 900 A | 200 km/h | manual p. 8.2 | |
| SR/S 2022 | 75-10 | 82 | 111 | 190 | 900 A | 200 km/h | manual p. 8.18 | |
| SR/S 2023 | 75-10 | 82 | 111 | 190 | 900 A | 200 km/h | manual p. 8.18 | |
| SR/S 2024 | 75-10 | 84 | 114 | 190 | 900 A | 200 km/h | Full Power | manual p. 8.30 |
| SR/S 2025 | 75-10 | 83 | 113 | 190 | 900 A | 200 km/h | Full Power | manual p. 8.30 |
| DSR 2024 | 75-10X | 60 | 82 | 195 | 765 A | 167 km/h | Full Power | manual p. 8.14 |
| DSR 2025 | 75-10X | 60 | 82 | 195 | 765 A | 167 km/h | Full Power | manual p. 8.14 |
| DSR/X 2023 | 75-10 5T | 75 | 102 | 225 | 900 A | 180 km/h | manual p. 8.2 | |
| DSR/X 2024 | 75-10X | 75 | 102 | 229 | 900 A | 180 km/h | Full Power | manual p. 8.22 |
| DSR/X 2025 | 75-10X | 75 | 102 | 229 | 900 A | 180 km/h | Full Power | manual p. 8.22 |
| DSR/X 2026 | 75-10X | 75 | 102 | 229 | 900 A | 180 km/h | Full Power | manual p. 8.14 |
- FX 201475-533 kW · 95 Nm · 420 A · 137 km/h
- FX 201575-533 kW · 95 Nm · 420 A · 137 km/h
- FX 201675-533 kW · 95 Nm · 420 A · 137 km/h
- FX 201775-532.7 kW · 106 Nm · 550 A · 137 km/h
- FX 201875-533 kW · 106 Nm · 550 A · 137 km/h
- FX 201975-533 kW · 106 Nm · 550 A · 137 km/h
- FX 202075-533 kW · 106 Nm · 550 A · 137 km/h
- FX 202175-533 kW · 106 Nm · 550 A · 137 km/h
- FX 202275-533 kW · 106 Nm · 550 A · 137 km/h
- FX 202375-533 kW · 106 Nm · 550 A · 137 km/h
- FX 202475-534 kW · 106 Nm · 550 A · 137 km/h
- FX 202575-534 kW · 106 Nm · 550 A · 137 km/h
- FXE 202275-533 kW · 106 Nm · 550 A · 132 km/h
- FXE 202375-533 kW · 106 Nm · 550 A · 132 km/h
- FXE 202475-534 kW · 106 Nm · 550 A · 137 km/h
- FXE 202575-534 kW · 106 Nm · 550 A · 137 km/h
- FXS 201675-533 kW · 95 Nm · 420 A · 132 km/h
- FXS 201775-532.7 kW · 106 Nm · 550 A · 137 km/h
- FXS 201875-533 kW · 106 Nm · 550 A · 132 km/h
- FXS 201975-533 kW · 106 Nm · 550 A · 132 km/h
- FXS 202075-533 kW · 106 Nm · 550 A · 132 km/h
- FXS 202175-533 kW · 106 Nm · 550 A · 132 km/h
- DS 201675-740 kW · 92 Nm · 420 A · 158 km/hZF13.0 · Zero spec page
- DS 201775-745 kW · 110 Nm · 550 A · 158 km/h
- DS 201875-745 kW · 110 Nm · 550 A · 158 km/h
- DS 201975-745 kW · 110 Nm · 550 A · 158 km/h
- DS 202075-745 kW · 110 Nm · 550 A · 158 km/h
- DS 202175-744 kW · 109 Nm · 550 A · 139 km/h11kW, ZF14.4 · manual p. 8.6
- DS 202275-744 kW · 109 Nm · 550 A · 139 km/h11kW · manual p. 8.4
- DS 202375-744 kW · 109 Nm · 550 A · 139 km/h11kW · manual p. 8.4
- DS 202475-751 kW · 132 Nm · 600 A · 167 km/hFull Power · manual p. 8.6
- DS 202575-751 kW · 132 Nm · 600 A · 167 km/hFull Power · manual p. 8.6
- DS 202675-751 kW · 132 Nm · 600 A · 167 km/hFull Power · manual p. 8.6
- S 201475-740 kW · 92 Nm · 420 A · 153 km/h
- S 201575-740 kW · 92 Nm · 420 A · 158 km/h
- S 201675-740 kW · 92 Nm · 420 A · 153 km/hZF13.0 · Zero spec page
- S 201775-745 kW · 110 Nm · 550 A · 158 km/h
- S 201875-745 kW · 110 Nm · 550 A · 153 km/h
- S 201975-745 kW · 110 Nm · 550 A · 153 km/h
- S 202075-745 kW · 110 Nm · 550 A · 153 km/h
- S 202175-744 kW · 109 Nm · 550 A · 139 km/h11kW, ZF14.4 · manual p. 8.2
- S 202275-744 kW · 109 Nm · 550 A · 139 km/h11kW · manual p. 8.2
- S 202375-744 kW · 109 Nm · 550 A · 139 km/h11kW · manual p. 8.2
- S 202475-751 kW · 132 Nm · 600 A · 167 km/hFull Power · manual p. 8.6
- S 202575-751 kW · 132 Nm · 600 A · 167 km/hFull Power · manual p. 8.6
- S 202675-751 kW · 132 Nm · 600 A · 167 km/hFull Power · manual p. 8.6
- SR 201475-750 kW · 144 Nm · 660 A · 164 km/h
- SR 201575-750 kW · 144 Nm · 660 A · 164 km/h
- DSR 201675-7R50 kW · 144 Nm · 660 A · 158 km/h
- DSR 201775-7R51.5 kW · 146 Nm · 775 A · 164 km/h
- DSR 201875-7R52 kW · 146 Nm · 775 A · 158 km/h
- DSR 201975-7R52 kW · 146 Nm · 775 A · 158 km/h
- DSR 202075-7R52 kW · 146 Nm · 775 A · 163 km/h
- DSR 202175-7R52 kW · 146 Nm · 775 A · 163 km/h
- DSR 202275-7R52 kW · 146 Nm · 775 A · 163 km/h
- DSR 202375-7R52 kW · 146 Nm · 775 A · 163 km/h
- SR 201675-7R50 kW · 144 Nm · 660 A · 164 km/h
- SR 201775-7R51.5 kW · 146 Nm · 775 A · 164 km/h
- SR 201875-7R52 kW · 146 Nm · 775 A · 164 km/h
- SR 201975-7R52 kW · 146 Nm · 775 A · 164 km/h
- SR 202075-7R52 kW · 146 Nm · 775 A · 163 km/h
- SR 202175-7R52 kW · 146 Nm · 775 A · 163 km/h
- SR 202275-1055 kW · 166 Nm · 900 A · 167 km/h
- SR 202375-1055 kW · 166 Nm · 900 A · 167 km/h
- SR 202475-1064 kW · 166 Nm · 785 A · 167 km/hFull Power · manual p. 8.14
- SR 202575-1064 kW · 166 Nm · 785 A · 167 km/hFull Power · manual p. 8.14
- SR/F 202075-1082 kW · 190 Nm · 900 A · 200 km/h
- SR/F 202175-1082 kW · 190 Nm · 900 A · 200 km/h
- SR/F 202275-1082 kW · 190 Nm · 900 A · 200 km/h
- SR/F 202375-1082 kW · 190 Nm · 900 A · 200 km/h
- SR/F 202475-1084 kW · 190 Nm · 900 A · 200 km/hFull Power · manual p. 8.22
- SR/F 202575-1083 kW · 190 Nm · 900 A · 200 km/hFull Power · manual p. 8.22
- SR/F 202675-1083 kW · 190 Nm · 900 A · 200 km/hFull Power · manual p. 8.14
- SR/S 202075-1082 kW · 190 Nm · 900 A · 200 km/h
- SR/S 202175-1082 kW · 190 Nm · 900 A · 200 km/h
- SR/S 202275-1082 kW · 190 Nm · 900 A · 200 km/h
- SR/S 202375-1082 kW · 190 Nm · 900 A · 200 km/h
- SR/S 202475-1084 kW · 190 Nm · 900 A · 200 km/hFull Power · manual p. 8.30
- SR/S 202575-1083 kW · 190 Nm · 900 A · 200 km/hFull Power · manual p. 8.30
- DSR 202475-10X60 kW · 195 Nm · 765 A · 167 km/hFull Power · manual p. 8.14
- DSR 202575-10X60 kW · 195 Nm · 765 A · 167 km/hFull Power · manual p. 8.14
- DSR/X 202375-10 5T75 kW · 225 Nm · 900 A · 180 km/h
- DSR/X 202475-10X75 kW · 229 Nm · 900 A · 180 km/hFull Power · manual p. 8.22
- DSR/X 202575-10X75 kW · 229 Nm · 900 A · 180 km/hFull Power · manual p. 8.22
- DSR/X 202675-10X75 kW · 229 Nm · 900 A · 180 km/hFull Power · manual p. 8.14
What the motor tells you while you ride
The motor carries a temperature sensor, and its reading is in the logs and on the dash. On the SR/F the gauge stays white from 20 °C to 118 °C and turns red from 118 °C to 150 °C. The S and DS dashes have two warning codes for it, "Motor Temperature Warning Stage 1" and "Stage 2". A hot motor gets less current from the controller, so power and torque drop until it cools.
Zero gives a riding example of how that happens: holding the bike on a hill with part throttle heats the motor and can limit peak power and torque until it cools, so the brakes are the better way to stand still.
The motor has no oil and no brushes. The one motor item in Zero's maintenance schedule is "Drive Motor: commissioning and timing", the encoder check above.
What is Zero's and what is drawn
From Zero: every power, torque, speed, current, gearing and tyre figure; the motor names and magnet wording; the ten poles, the rotor lengths of the 75-5 and 75-7, the stator pressed into the case, the bearings and the 75-5's weight; the encoder, its offset sticker and commissioning; the case shapes, which follow Zero's photos and the service manual pictures.
Not from Zero: the twelve stator teeth and the magnet layout in the 3D model, every dimension other than the case diameters, the 10 cm rotor of the 75-10, and the shape of the torque curve between the two peak figures. The field-weakening angle shown in the readouts is illustrative: Zero does not publish how its controllers set it.
Frequently asked questions
How many poles does a Zero Z-Force motor have?
Ten: five north and five south. Zero's report on the motor to the California Energy Commission says the design moved from 20 poles to 10 so the controller of the time could drive it fast enough. Zero does not publish the number of stator teeth.
What does the 7 in Z-Force 75-7 mean?
The rotor length in centimetres. Zero's report gives 7 cm for the 75-7 and 5 cm for the 75-5. A longer rotor carries more magnet and gives more torque for the same current. The 10 in 75-10 follows the same naming, but Zero has not stated it.
Why does my S make less power than another S of the same year?
Different versions. In Europe the 2024 to 2026 S comes as an A1 version with 45 kW peak and 139 km/h, and as a full-power version with 51 kW and 167 km/h, both with the 75-7. From 2017 to 2023 an S or DS with the smaller battery had the 75-5 motor instead of the 75-7. Your bike's owner's manual lists each version.
Why does a Zero have only one gear?
Because its motor gives full torque from a standstill and still pulls at several thousand rpm, so one belt reduction covers the whole speed range. Since 2017 most Zeros use a 20-tooth pulley and a 90-tooth sprocket, 4.50:1; the FX family uses 5.00:1 and the DSR/X 4.09:1. The top speed is set by the controller, not by the gearing.
Is the Zero motor air-cooled or liquid-cooled?
Air-cooled, passively: no fan and no coolant. The stator is pressed into the finned case and the air going past takes the heat away. When the motor gets hot the controller limits current until it cools.
What voltage and current does the Zero motor run on?
The battery is 28 cells in series, 102 V nominal and about 117 V full. The controller ratings Zero prints run from 420 A (2014 FX, S and DS) to 900 A (SR/F, SR/S and DSR/X).
Does the motor need maintenance?
It has no oil and no brushes. Zero's schedule lists one motor item, "Drive Motor: commissioning and timing", the check that the encoder and controller agree on the rotor's position. The belt and its pulley are maintained separately.
Power and torque for 2014 to 2016 are from Zero's spec pages of those years as archived (two are listed; the others are in the dataset behind this page). Where Zero's 2015 spec page and owner's manual disagree on the S's top speed (153 and 158 km/h), the table uses the manual.
Sources:
- [1] California Energy Commission: Zero Motorcycles, "Next Generation Electric Motorcycle Drivetrain", report CEC-600-2020-037 (2020) (opens in a new tab)
- [2] Zero Motorcycles: 2016 press kit (75-5, 75-7 and their IPM versions, 75-7R) (opens in a new tab)
- [3] RLS: Zero Motorcycles case study (the motor encoder) (opens in a new tab)
- [4] Zero Motorcycles: 2014 S, SR and DS owner's manual, pp. 1.6-1.10 (motor, controller, top speed) (opens in a new tab)
- [5] Zero Motorcycles: 2016 S, SR, DS and DSR owner's manual, pp. 8.1-8.7 (surface and interior magnets by battery, 75-7R) (opens in a new tab)
- [6] Zero Motorcycles: 2016 FX and FXS owner's manual, pp. 8.1-8.3 (opens in a new tab)
- [7] Zero Motorcycles: 2021 S, SR, DS and DSR owner's manual, pp. 6.5, 7.6 and 8.2-8.8 (opens in a new tab)
- [8] Zero Motorcycles: 2021 SR/F owner's manual, pp. 4.12 and 8.2 (opens in a new tab)
- [9] Zero Motorcycles: 2024 S, SR, SR/F and SR/S owner's manual (Europe), pp. 8.2-8.30 (A1, A2 and full-power versions) (opens in a new tab)
- [10] Zero Motorcycles: 2024 DS, DSR and DSR/X owner's manual (Europe), pp. 8.2-8.22 (opens in a new tab)
- [11] Zero Motorcycles: 2023 DSR/X owner's manual, p. 8.2 (Z-Force 75-10 5T) (opens in a new tab)
- [12] Zero Motorcycles: 2026 S and SR/F owner's manual (Europe), p. 2.2 (hill-holding heats the motor) (opens in a new tab)
- [13] Zero Motorcycles: S, SR and SR/F service manual 8811935-AJ, pp. 10-14, 30-9 and 30-20 (opens in a new tab)
- [14] Zero Motorcycles: FST and ADV service manual 8811933-AL, p. 30-17 (opens in a new tab)
- [15] Zero Motorcycles: S and DS service manual 8811965-AD, pp. 1-11, 30-3, 30-8 and 30-18 (opens in a new tab)
- [16] Zero Motorcycles: Zero S spec page, 2014, archived (opens in a new tab)
- [17] Zero Motorcycles: Zero FX spec page, 2014, archived (opens in a new tab)
- [18] Zero Motorcycles: Zero S model page (shares the SR/F's motor hardware) (opens in a new tab)
- [19] Sustainable Skies: "New Zero powerplants" (2015, a Zero engineer on the 75-7's weight) (opens in a new tab)
Figures are Zero's own, from its owner's and service manuals and its published material. The 3D model is a drawing based on them, not a dimensioned part. For any work on the motor, follow the service manual for your model year: the motor, controller and their cables carry battery voltage.